Melody at 09:37, 22 November 2023

2023-11-22T09:37:22Z

Melody: Created page with "=='''Product name'''== LCPI PC H6 V3 computer development board Allwinner H6 chip open source programming MCU/with EMMC.
=='''Introduction'''== 1.Board size:85*56mm..."

2023-11-22T09:13:40Z

Created page with "=='''Product name'''== LCPI PC H6 V3 computer development board Allwinner H6 chip open source programming MCU/with EMMC. =='''Introduction'''== 1.Board size:85*56mm..."

New page

=='''Product name'''==
LCPI PC H6 V3 computer development board Allwinner H6 chip open source programming MCU/with EMMC. 

=='''Introduction'''==
1.Board size:85*56mm Weight:35g 
[[File:LCPIH6-1-1.jpg]] 

[[File:LCPIH6-2-1.jpg]] 

[[File:LCPIH6-3.jpg]] 

2.Introduce for GPIO Pin 
[[File:LCPIH6-4.jpg]] 

[[File:LCPIH6-5.jpg]] 

=='''Overview'''==
LCPI PC H6 V3 uses Allwinner H6 Cortex-53 quad-core processor, supports Android7.0, Ubuntu and Debian and other operating systems, with a main frequency of 1.5 GHz and ultra-low power consumption. Adopt Mali-720 MP2 GPU, support 1080P video encoding, H.264 hard decoding. 

=='''Function'''==
*CPU:Allwinner H6 Quad Core 1.8GHz 64-bit ARM Cortex-A53 
*GPU:Mali-720 MP2 GPU 
*Memory:1GB LPDDR3 (shared with GPU) 
*Support memory card:onboard self-popping TF card holder,maximum support 64GB TF card 
*Onboard EMMC:8G EMMC memory chip,faster and more stable than TF card 
*Ethernet:10/100M RJ45 Ethernet interface 
*WiFi:onboard AP6212 2.4GHz WiFi transmission chip and IPEX antenna interface 
*Video output:HDMI,support connection with LCD monitor/TV with HDMI 
*Audio output:HDMI 
*USB2.0:1 USB 2.0 Host interface,1 USB OTG 2.0 
*USB3.0:1 USB 3.0 interface 
*Infrared:Onboard infrared receiver,the development board can be controlled by remote control 
*GPIO:On-board 2.54mm 2*13Pin GPIO pin header 
*UART:On-board 2.54mm 1X3Pin UART (GND, TX, RX) pin header 
*Buttons:On-board power button,reset button and upgrade button 
*LED light:On-board status indicator 
*Power supply:5V Type-C USB power input,MicroUSB (USB) 
*Supported systems:Android7.0,Ubuntu,Debian and other operating systems 

=='''System burning'''==
'''1. Burn Android system to SD card''' 
The development board can boot the system from SD. The following is how to burn the system to the SD card: 
Insert the SD card into the computer, open the PhonixCard software, click "固件" to load the Image system file, select "启动卡", click "烧卡", after the programming is completed, insert the card into the SD card slot, and power on the development board again can. 
[[File:LCPIH6-6.png]] 

'''2.Burn Android system to EMMC'''

← Older revision		Revision as of 09:37, 22 November 2023
Line 58:		Line 58:

	'''2.Burn Android system to EMMC'''<br>		'''2.Burn Android system to EMMC'''<br>
		+	Open the PhoenixSuit software, load the system image file to be burned, and hold down the UBOOT key on the board. Then connect the computer USB port and the Micro USB port on the board through the Micro USB cable.<br>
		+	[[File:LCPIH6-7.png]] UBOOT key [[File:LCPIH6-8.png]] Micro USB interface<br>
		+
		+	After the software detects the inserted board, it will automatically enter programming<br>
		+	[[File:LCPIH6-9.png]]<br>
		+
		+	The interface after programming is completed<br>
		+	[[File:LCPIH6-10.png]]<br>
		+	''Remark:<br>
		+	If it cannot automatically enter the programming mode and prompts that there is no device connection, indicating that there is no USB driver, you can follow the steps below to install the driver:''<br>
		+	● Open the Device Manager, right-click on "Unknown Device" and select "Update Driver"<br>
		+	[[File:LCPIH6-11.png]]<br>
		+
		+	● Navigate to the driver directory under PhoenixSuit software<br>
		+	[[File:LCPIH6-12.png]]<br>
		+
		+	● After the driver is installed successfully, the following devices will be displayed<br>
		+	[[File:LCPIH6-13.png]]<br>
		+
		+
		+
		+
		+	=='''Android source code compilation'''==
		+	'''1. Virtual machine installation'''<br>
		+	Airsay provides customers with virtual machines that have built various compilation environments. You can directly install the virtual machine for compilation.<br>
		+	Proceed as follows:<br>
		+	①Download and unzip the Ubuntu_16.04_X64_H6_Android7.0.7z virtual machine file<br>
		+
		+	②Open the VMware Workstation software, click "打开虚拟机" and locate the folder you just extracted.<br>
		+	Ubuntu_16.04_X64.vmx file in Ubuntu_16.04_X64_H6_Android7.0<br>
		+	[[File:LCPIH6-14.png]]<br>
		+
		+	③Click the green play icon on the left or in the menu bar to "开启此虚拟机"<br>
		+	[[File:LCPIH6-15.png]]<br>
		+
		+	④After entering the Ubuntu system, click on the Test account and enter the password 123456 to enter the system.<br>
		+	[[File:LCPIH6-16.png]]<br>
		+
		+
		+	'''2.Source code compilation'''<br>
		+	①Click the H6-13.png icon and enter the path home/LC/H6/h6_android7.0<br>
		+	[[File:LCPIH6-17.png]]<br>
		+
		+	[[File:LCPIH6-18.png]]<br>
		+
		+	②Right-click the mouse in the h6_android7.0 directory and open the Terminal tool<br>
		+	●Enter ./make.sh all and press Enter
		+	[[File:LCPIH6-19.png]]<br>
		+
		+	After waiting for a period of time (depending on the computer configuration), complete this step<br>
		+	[[File:LCPIH6-20.png]]<br>
		+
		+	The image file output path is:<br>
		+	/home/LC/H6/h6_android7.0/result/sun50iw6p1_android_petrel-p1_uart0.img<br>
		+
		+
		+
		+
		+	=='''Download LCPI-H6 User Manual'''==
		+	For more information about the use of LCPI-H6, please click [https://drive.google.com/drive/folders/1vMBev16LPKjWOGpATTJt-X00QW34F3cd?spm=a2g0o.detail.1000023.1.17aa3uQ93uQ9MA Google Drive Link]<br>

LC-PI-H6 - Revision history

Melody at 09:37, 22 November 2023

Melody: Created page with "=='''Product name'''== LCPI PC H6 V3 computer development board Allwinner H6 chip open source programming MCU/with EMMC. =='''Introduction'''== 1.Board size:85*56mm..."

Melody: Created page with "=='''Product name'''== LCPI PC H6 V3 computer development board Allwinner H6 chip open source programming MCU/with EMMC.
=='''Introduction'''== 1.Board size:85*56mm..."